Measure true density of battery materials with the DensiPyc 1000. See how helium pycnometry supports QC of cathode and anode materials with RSD below 0.1%.
Metal crystallite size is one of the most consequential structural parameters in supported metal catalyst characterization. It determines how much of the active metal is surface-exposed, how the catalyst will respond to sintering during operation, and whether a new synthesis method has actually produced a better-dispersed material than the previous one. Reporting crystallite size as the average metal particle diameter creates a common basis for comparing catalysts prepared in different laboratories or by different routes, regardless of which characterization method was used.
Volumetric chemisorption is a static measurement technique in which a known quantity of reactive gas is introduced into a closed vacuum system containing the catalyst sample. The gas adsorbs on the metal surface, and the resulting pressure decrease at constant volume and temperature provides the data needed to calculate how much gas was taken up by the catalyst. Because the technique is static rather than flow-based, it measures the equilibrium adsorption of the probe gas on the catalyst surface. This is a key distinction from pulse chemisorption, which is a dynamic technique. In volumetric chemisorption, both strongly bound (irreversible) and weakly bound (reversible) adsorbate species are captured because the measurement is made at equilibrium rather than under flowing inert carrier gas that would sweep weakly held species away. The two types are operationally defined: reversible chemisorption refers to the fraction that can be removed by brief evacuation at ambient temperature, while irreversible chemisorption remains after this treatment. Both are accessible from the volumetric measurement. The adsorbate gases most commonly used are H2, O2, and CO, all of which adsorb selectively on the metal surface without interacting with typical oxide supports such as Al2O3, SiO2, or TiO2. The uptake, expressed as moles of gas adsorbed per gram of catalyst, is the primary experimental output.
Equipment and Setup A volumetric chemisorption instrument consists of a vacuum system with precisely known internal volumes, a pressure transducer capable of accurate measurement at sub-atmospheric pressures below 1 atm, and a sample cell connected to the manifold. The system design, shown schematically in Figure 1a of the source document, includes a known manifold volume Vk and a sample volume Vs containing the catalyst. The pressures and temperatures employed in volumetric chemisorption allow the use of the ideal gas law (PV = nRT, Equation 1) to calculate the number of moles of gas in the system from pressure measurements at known volume and temperature. The Measurement Sequence The measurement proceeds as follows for each point on the isotherm: A known quantity of gas is introduced into the manifold volume Vk at an initial pressure Pi and temperature T. The number of moles introduced is calculated from Pi, Vk, R, and T using the ideal gas law. The gas is then expanded into the sample volume Vs by opening the valve connecting the manifold to the sample cell. The system is allowed to reach adsorption equilibrium at a final pressure Pf. The number of moles adsorbed by the catalyst is the difference between the moles introduced and the moles remaining in the gas phase at equilibrium, calculated from Equation 2: n_ads = n_i minus [Pf(Vk + Vs) / RT] This measurement is repeated at increasing gas quantities to generate a complete isotherm of moles adsorbed versus equilibrium pressure. Extrapolation of this isotherm to zero pressure yields the total chemisorption uptake, representing the monolayer saturation of all accessible metal sites.
The Role of Adsorption Stoichiometry The chemisorption uptake tells you how much gas was adsorbed. Converting that number into a count of surface metal atoms and then into an average crystallite size requires knowledge of the adsorbate-metal stoichiometry: how many adsorbate atoms or molecules bind per surface metal atom. The conventional assumption is that chemisorption is limited to one monolayer on surface metal atoms only, with a constant and well-defined number of adsorbate molecules per surface site. Under this assumption, the number of surface metal atoms is directly calculable from the uptake and the stoichiometric factor. Established Stoichiometric Factors for Common Systems Extensive experimental work over the past several decades has established adsorption stoichiometries for many common metal-adsorbate combinations. Table 1 of the source document lists the experimentally derived stoichiometric factors for H2 and CO chemisorption on nickel and platinum:
Metal |
Adsorbate |
Stoichiometric Factor (SF) |
|---|---|---|
Ni |
H2 |
H_ads : Ni_surf = 1:1 |
Ni |
CO |
CO_ads : Ni_surf = 0.5 to 3:1 |
Pt |
H2 |
H_ads : Pt_surf = 1:1 |
For these well-characterized systems, volumetric chemisorption has become a routine crystallite size determination tool because the stoichiometry is known and validated. A Critical Note on Stoichiometric Factor Definitions An important source of apparent inconsistency in the literature is that different sources may use different definitions of the stoichiometric factor, depending on how uptake is defined. If uptake is expressed as moles of H2 per metal atom, then SF = 0.5, because each H2 molecule dissociates into two atomic H adsorbates, each binding to one metal atom. If uptake is expressed as moles of atomic H per metal atom, then SF = 1. Both conventions appear in the literature and both are internally consistent. What matters is that the convention used in the stoichiometry determination matches the convention used in the crystallite size calculation. Mixing definitions produces incorrect results. Temperature Dependence of Stoichiometry Each stoichiometric factor in Table 1 was determined under a specific set of experimental conditions. These ratios can change with temperature because adsorption geometry and coverage patterns on metal surfaces are temperature-dependent. There is no universally correct stoichiometry or standard experimental condition for volumetric chemisorption. The measurement must always be carried out under the same conditions used to establish the stoichiometric factor for that specific metal-adsorbate combination. For new adsorbate-metal systems without established stoichiometry, the stoichiometric factor must be determined independently using an alternative crystallite size measurement such as TEM or XRD.
Because volumetric chemisorption is a static equilibrium measurement, it captures both irreversible and reversible chemisorption simultaneously. This is both an advantage and a consideration that affects data interpretation. Irreversible chemisorption refers to strongly bound adsorbate species that remain on the metal surface after brief evacuation at ambient temperature. This fraction is attributed to the most energetically favorable binding sites and represents the most relevant active sites for catalysis. Reversible chemisorption refers to more weakly bound species that can be removed by evacuation. These may include adsorbate bound to lower-energy sites, or species that interact with both the metal surface and the support interface. A researcher who requires only the irreversible uptake can run two isotherms: one before evacuation and one after evacuating at ambient temperature. The difference between the two represents the reversible fraction. The total isotherm gives combined uptake. Depending on the catalyst system and the intended calculation, either or both values may be appropriate for crystallite size determination.
Volumetric chemisorption assumes that the measured uptake is the equilibrium value, meaning the maximum uptake achievable at the experimental temperature. This assumption is only valid if sufficient time has been allowed for the adsorption process to reach equilibrium at each pressure point on the isotherm. The time required to reach equilibrium depends on the metal, the adsorbate, and the temperature. For some systems this equilibration is complete within minutes. For others it may require hours or days. Experiments completed before equilibrium is reached will report erroneously low uptake values, which translate directly into overestimated crystallite sizes and underestimated dispersions. This is a practical risk in high-throughput environments where equilibration time criteria are set too tightly to meet daily measurement quotas. For a new metal-adsorbate system where equilibration kinetics are unknown, the appropriate approach is to vary the equilibration time and confirm that the measured uptake has stabilized before treating the result as an equilibrium value. For well-characterized systems, equilibration time requirements are typically documented alongside the stoichiometric factor data and should be followed as part of the measurement protocol.
Volumetric chemisorption produces the same primary output as temperature-programmed desorption: an uptake expressed as moles of gas adsorbed per gram of catalyst. Both convert this uptake into crystallite size using the same stoichiometric factors. The practical differences between the two approaches are relevant to laboratory workflow decisions:
Volumetric chemisorption captures both irreversible and reversible uptake, providing more complete information about the full adsorption energy distribution. Dynamic methods under inert gas flow may miss the reversible fraction.
Volumetric chemisorption requires longer equilibration times, particularly for activated chemisorption systems. A single five-point isotherm can require six hours or more.
For systems where equilibration is fast and only total uptake is needed, dynamic pulse chemisorption provides a faster path to the same crystallite size result.
For systems where reversible versus irreversible adsorption must be distinguished, or where equilibration kinetics are slow at ambient temperature, volumetric chemisorption is the more complete measurement.
The choice between the two methods depends on the specific metal-adsorbate system, the information required, and the throughput constraints of the laboratory. For well-characterized fast-equilibrating systems, pulse chemisorption is often preferred. Volumetric chemisorption remains the reference technique for establishing stoichiometric factors and for systems where the full adsorption isotherm is needed.
Reliable volumetric chemisorption requires an instrument capable of accurate P-V-T measurements at sub-atmospheric pressures, precise vacuum control, stable temperature management, and the flexibility to run both static volumetric and dynamic chemisorption measurements on the same platform. The AMI 300 Chemisorption Analyzer is AMI's flagship platform for fully automated static and dynamic chemisorption in a single configurable instrument. Static volumetric chemisorption, pulse chemisorption, and temperature-programmed desorption are all supported within the same system, enabling a researcher to run both a volumetric isotherm and a pulse measurement on the same catalyst sample without changing instruments or rebuilding the experimental setup. Precision gas control with independent mass flow controllers and a double thermocouple design for accurate temperature measurement ensure that the P-V-T measurement conditions are stable throughout the equilibration period. Sample holder options accommodate powders, pellets, extrudates, and honeycomb cores, covering the full range of supported catalyst forms encountered in research and production. The AMI 400 offers the same measurement capabilities with an automatic intelligent gas interface that selects the appropriate gas for each protocol step without manual switching, and a triple thermocouple design for enhanced temperature control and safety. Both instruments support the adsorbate gases used in established volumetric chemisorption stoichiometry systems, including H2 and CO. For laboratories that need to run both the reference volumetric isotherm and faster routine dynamic measurements on a common instrument platform, the AMI 300 and AMI 400 provide that capability without requiring separate dedicated systems.
Volumetric chemisorption is one of the most thoroughly validated methods for determining metal crystallite size in supported catalysts. Its foundation in the ideal gas law makes the calculation transparent. Its ability to measure both irreversible and reversible adsorption provides information about the full adsorption energy distribution that dynamic techniques may not capture. And its connection to decades of published stoichiometry data for common metal-adsorbate systems makes crystallite size determination a routine measurement for well-characterized catalyst families. The three variables that most affect volumetric chemisorption accuracy are stoichiometric factor selection, consistency with the experimental conditions used to establish that factor, and allowing sufficient equilibration time at each pressure point. Errors in any one of these three areas produce uptake values that are physically real but analytically incorrect: the measurement is internally consistent but does not reflect the true crystallite size. For research programs developing new catalyst formulations and for quality control programs monitoring batch-to-batch consistency, volumetric chemisorption provides the quantitative foundation for crystallite size comparison across different preparation methods, laboratories, and instrument platforms.
1. Boudart, M. Catalysis by supported metals. Adv. Catal. 1969, 20, 153-166. 2. Gogate, M. R. Recent research advances and critical assessment of methods to determine the particle size in supported metals. Appl. Catal. A., 2016, 514, 203-213. 3. Greegor, R. B. and Lytle, F. W. Morphology of supported metal clusters: Determination by EXAFS and chemisorption. J. Catal. 1980, 63, 476-486. 4. Mustard, D. G. and Bartholomew, C. H. Determination of metal crystallite size and morphology in supported nickel catalysts. J. Catal. 1981, 67, 186-206. 5. Blackmond, D. G. and Ko, E. I. Structural sensitivity of CO adsorption and H2CO coadsorption on NiSiO2 catylsts. J. Catal. 1985, 96, 210-221. 6. Spenadel, L. and Boudart, M. Dispersion of platinum on supported catalysts. J. Phys. Chem. 1950, 64, 204-207.
In volumetric chemisorption, the total measured uptake includes both strongly bound (irreversible) and weakly bound (reversible) adsorbate species. Reversible chemisorption refers to the fraction that can be removed by brief evacuation at ambient temperature. Irreversible chemisorption is the fraction that remains after this treatment. To separate the two contributions, a researcher runs the full isotherm before evacuation, evacuates the sample, then runs a second isotherm. The difference between the two isotherms represents the reversible fraction. The choice of which value to use for crystallite size calculation depends on the catalyst system and the stoichiometry convention applied. For more on how this compares with dynamic methods, see our comparison of static and dynamic chemisorption methods.
Adsorption geometry on metal surfaces is temperature-dependent. The fraction of CO adsorbed in linear versus bridged configurations on nickel, for example, changes with temperature, which changes the effective stoichiometric factor. Since crystallite size is calculated directly from uptake divided by the stoichiometric factor, an incorrect stoichiometry produces a proportionally incorrect crystallite size. The practical consequence is that volumetric chemisorption experiments must be performed at the same temperature used to establish the stoichiometric factor in the source literature. There is no universally correct experimental temperature and no standard stoichiometry that applies independent of conditions. For the established stoichiometric factors for H2 and CO on Ni and Pt, see our metal dispersion by pulse chemisorption article for context on how stoichiometry choices affect calculated dispersion.
Equilibration time depends on the metal, adsorbate, and temperature. For some systems equilibration is complete within minutes. For activated chemisorption systems such as H2 on cobalt at ambient temperature, equilibration may require hours, or the measurement must be performed at elevated temperature to achieve reasonable kinetics. If the isotherm is collected before true equilibrium is reached at each pressure point, the measured uptake will be lower than the true equilibrium value. This causes the calculated crystallite size to be larger than the actual value and the calculated dispersion to be lower. For a new metal-adsorbate system, the only reliable way to confirm equilibration is to vary the equilibration time per point and verify that the measured uptake does not increase with additional waiting time. See our chemisorption analysis adsorbate selection guide for guidance on equilibration conditions for common catalyst systems.
The method measures total gas uptake using pressure–volume–temperature relationships. From this:
Gas uptake → number of surface metal atoms
Surface atoms → average particle (crystallite) size
This relies on known chemisorption stoichiometry between the gas and the metal.
Volumetric chemisorption, also known as static chemisorption, is a technique that measures how much gas adsorbs on a catalyst surface under equilibrium conditions. It is widely used for metal surface area measurement and metal crystallite size determination.
Measure true density of battery materials with the DensiPyc 1000. See how helium pycnometry supports QC of cathode and anode materials with RSD below 0.1%.
Learn how SSITKA in catalysis measures surface intermediates and kinetic parameters under true steady-state conditions, with ethylene oxidation and FT synthesis data.
SSITKA reveals surface kinetics and intermediate coverage under real reaction conditions. See how AMI’s AMI-300 SSITKA delivers precise catalytic data.
Learn how temperature programmed oxidation with methanation and FID detection detects carbon below 0.1% and distinguishes coke types on catalyst surfaces.